# Wireguard Help getting setup **URL:** \ **Category:** Networking Solutions\ **Created:** [November 23, 2023, 7:51am UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887 "2023-11-23T07:51:51Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![Raymond](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/r/c57346/32.png) [@Raymond](https://community.teltonika.lt/u/Raymond)\ **Post date:** [November 23, 2023, 7:51am UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/1 "2023-11-23T07:51:51Z")
OpenVPN is simply too slow on the RUTx11 so I’m looking to try a wireguard service. Is there a commercial wireguard provider that just works with this router? I’m looking for one that is easy to get running? Is there an up to date walkthrough of setting one of these services up? It’s so easy to get ExpressVPN working on the router. Is there something like this for wireguard? ---
**Author:** ![Raymond](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/r/c57346/32.png) [@Raymond](https://community.teltonika.lt/u/Raymond)\ **Post date:** [November 28, 2023, 11:36am UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/2 "2023-11-28T11:36:37Z")
crickets… Here’s the config file I received from Mullvad (I’ve changed the details to be dummy values) [Interface] # Device: Crowd Source PrivateKey = YDaCY901e56d25939a82b0a57f1f92a0943b5Xh9UXc= Address = 100.615.62.13/32,fbb0:ccff:ccff:bb01::1:4ac/128 DNS = 10.614.0.213 PostUp = iptables -I OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -m addrtype ! --dst-type LOCAL -j REJECT && ip6tables -I OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -m addrtype ! --dst-type LOCAL -j REJECT PreDown = iptables -D OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -m addrtype ! --dst-type LOCAL -j REJECT && ip6tables -D OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -m addrtype ! --dst-type LOCAL -j REJECT [Peer] PublicKey = vnD/2bCGqH901e56d25939a82b0a57f1f92a0943b5a= AllowedIPs = 0.0.0.0/0,::0/0 Endpoint = 19.269.155.10:5212 Can ANYONE tell me how to get this information into the RutX11 so I can get wireguard set up? My goal is to have everything run through wireguard unless I flip the enable switch off in the GUI then I just want data to flow directly out. Basically just like OpenVPN works on the router (only faster). If this isn’t the right place to get support, where should I go? ---
**Author:** ![Raymond](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/r/c57346/32.png) [@Raymond](https://community.teltonika.lt/u/Raymond)\ **Post date:** [November 28, 2023, 11:48am UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/3 "2023-11-28T11:48:28Z")
Look at this little router company that put a great and easy to follow set of instructions online: > **[Mullvad Guide](https://www.gl-inet.com/solutions/vpn/mullvad/)** > > Home Solutions VPN on Router Mullvad Setup Guide GL.iNet setup with Mullvad > GET Mullvad Tutorial This tutorial explains how to connect your GL.iNet router to Mullvad using the WireGuard protocol. > STEP.1 Access Mullvad website to make sure the... Teltonika, please do the same ---
**Author:** ![flebourse](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/f/8797f3/32.png) [@flebourse](https://community.teltonika.lt/u/flebourse)\ **Post date:** [November 28, 2023, 12:14pm UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/4 "2023-11-28T12:14:25Z")
Hello, This is a public forum, don’t post private or public keys here. > [@Raymond](#): > > Address = 100.615.62.13/32 > [@Raymond](#): > > DNS = 10.614.0.213 > [@Raymond](#): > > Endpoint = 19.269.155.10 This is obviously wrong, bytes have values between 0 and 255. > [@Raymond](#): > > AllowedIPs = 0.0.0.0/0,::0/0 The values above will interfere with the default route, use 0.0.0.0/1,128.0.0.0/1,::0/1,8000::0/1 instead. Routing all traffic through wireguard interfaces is tricky there are several posts about the subject, look [here](https://community.teltonika.lt/t/routing-all-traffic-through-a-wireguard-interface/2512/1) for example. Regards, ---
**Author:** ![Raymond](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/r/c57346/32.png) [@Raymond](https://community.teltonika.lt/u/Raymond)\ **Post date:** [November 28, 2023, 12:37pm UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/5 "2023-11-28T12:37:59Z")
Please read what I wrote. I said I replaced all of the real values with dummy values… Why is it tricky? My cheap travel router took 2 minutes to get set up. ---
**Author:** ![flebourse](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/f/8797f3/32.png) [@flebourse](https://community.teltonika.lt/u/flebourse)\ **Post date:** [November 28, 2023, 12:41pm UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/6 "2023-11-28T12:41:33Z")
You can’t route all traffic through the wg interface blindly, there must be an exception for packets to the wg server itself. ---
**Author:** ![Raymond](https://community.teltonika.lt/letter_avatar_proxy/v4/letter/r/c57346/32.png) [@Raymond](https://community.teltonika.lt/u/Raymond)\ **Post date:** [November 28, 2023, 1:32pm UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/7 "2023-11-28T13:32:27Z")
I’ll just switch to the travel router since it is MUCH easier to set up and it “just works”. You guys need to update your firmware to address this complication. ---
**Author:** ![system](https://community.teltonika.lt/user_avatar/community.teltonika.lt/system/32/15707_2.png) [@system](https://community.teltonika.lt/u/system)\ **Post date:** [December 8, 2023, 7:52am UTC](https://community.teltonika.lt/t/wireguard-help-getting-setup/2887/8 "2023-12-08T07:52:51Z")
Closed on December 8, 2023, 7:52am UTC This topic was automatically closed after 15 days. New replies are no longer allowed.