# ATC700: movement does not turn on GNSS in Online Sleep when Saving/sending mode is "After Time Sync"

**URL:** <https://community.teltonika.lt/t/atc700-movement-does-not-turn-on-gnss-in-online-sleep-when-saving-sending-mode-is-after-time-sync/21651>\
**Category:** Issue\
**Created:** [October 21, 2026, 6:22pm UTC](https://community.teltonika.lt/t/atc700-movement-does-not-turn-on-gnss-in-online-sleep-when-saving-sending-mode-is-after-time-sync/21651 "2026-10-21T18:22:32Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![setnicka](https://community.teltonika.lt/user_avatar/community.teltonika.lt/setnicka/32/26540_2.png) [@setnicka](https://community.teltonika.lt/u/setnicka)\
**Post date:** [October 21, 2026, 6:22pm UTC](https://community.teltonika.lt/t/atc700-movement-does-not-turn-on-gnss-in-online-sleep-when-saving-sending-mode-is-after-time-sync/21651/1 "2026-10-21T18:22:32Z")

</div>

Hello, I found another problem with my Teltonika ATC700 tracker (previous reports: [stops sending after queued commands](https://community.teltonika.lt/t/atc700-stops-sending-records-after-receiving-several-queued-gprs-commands/21506), [setparam response lost](https://community.teltonika.lt/t/atc700-setparam-response-is-lost-when-the-change-makes-the-device-reconnect/21507)). With Saving/sending mode “After Time Sync” (`107:2`), movement does not wake the device from Online Sleep, so GNSS stays off and the position freezes for days.

### Setup

**Device:** ATC700 (`Hw:ATC700 Mod:21`), FW `3.20.0-rc.1+7.exp.autonomous`, modem FW `EG915UEUABR03A01M08_01.215.01.215`

**Configuration:** Asset movement mode Movement (`12150:1`), Online Sleep (`102:3`), records every 30 s when moving and 300 s when stopped, Send period 0, `107:2` (“After Time Sync”).

### Problem

After the device falls asleep, movement is detected, the device switches to OnMove and saves a record every 30 s, but it sends only the last retained position (`io69` = 0, `GNSS Fix: 0`) even when the device is outside with good visibility of the sky. GNSS is never powered on. The only GNSS wake-ups come from `GPSD_PWU_CTRL`: once per hour for 60 s, cancelled after 3 failures (e.g. indoors). If the device falls asleep without a fix (`PWU no fix before activation`), there are none at all. The position stays frozen until a reboot, which helps only if GNSS gets a fix before the device sleeps again.

With `107:0` (After Position Fix) and otherwise the same configuration, movement wakes the device (`Reason: GNSS Fix`) and GNSS turns on as expected.

### Steps to reproduce

1. Set `107:2`, get a GNSS fix and leave the device indoors until it goes to sleep and the PWU attempts fail.
2. Walk outside.
3. The records arrive every 30 s, but GNSS stays off and the position does not change.

With `107:2` this happened every time between 16 and 20 Oct (4 occurrences, one of them a whole-day trip). With `107:0` GNSS turned on at every movement (7 times in 2 days).

### Logs (from the Dump)

With `107:2`, falling asleep with a fix and PWU giving up:

```auto
[M:SLEEP_MNG]: All sleep conditions met and TMO reached. Going to sleep...
[M:GPSD_PWU_CTRL]: PWU schedule wait due to fix
[M:GPSD_PWU_CTRL]: PWU scheduled timer for 3600s (state 1)
[M:GPSD_PWU_CTRL]: PWU sleep period elapsed, turn on GNSS
[M:GPSD_PWU_CTRL]: PWU wait fix failure - 1/3
...
[M:GPSD_PWU_CTRL]: PWU wait fix failure - 3/3
[M:GPSD_PWU_CTRL]: PWU cancel (1)

```

Then walking outside, `107:2` (no wake-up, no GNSS power transition):

```auto
[M:SCENARIOS_STATIC__ASSET_MOVEMENT]: Switching to OnMove state
[M:SCENARIOS_STATIC__ASSET_MOVEMENT_MODE_MOVEMENT]: GNSS source is Retained, switching to Main for OnMove state
[M:GPSD]: GNSS source changed to -> 1
[M:RECGEN]: Record Saved! ID:853
GNSS Fix: 0
[M:SLEEP_MNG__SEND_IN_SLEEP]: Send in sleep requested

```

The same situation with `107:0`:

```auto
[M:SCENARIOS_STATIC__ASSET_MOVEMENT]: Switching to OnMove state
[M:RECGEN]: Wake-up needed for GNSS fix
[M:SLEEP_MNG]: Wakeup triggered. Current Mode: Online Sleep, Reason: GNSS Fix
[M:SLEEP_MNG]: Woke up from Sleep Mode:
[M:GPSD]: GNSS power transition 0 -> 1

```

Dumps from both configurations are available. I can send them privately.

### Expected

In OnMove state the device should wake up and turn on GNSS regardless of the Saving/sending mode. With `107:2` the mode should only allow saving records without a fix, not stop GNSS from being used.

---

<div class="post-metadata">

**Author:** ![Imran.S](https://community.teltonika.lt/user_avatar/community.teltonika.lt/imran.s/32/22830_2.png) [@Imran.S](https://community.teltonika.lt/u/Imran.S)\
**Post date:** [November 12, 2026, 2:34am UTC](https://community.teltonika.lt/t/atc700-movement-does-not-turn-on-gnss-in-online-sleep-when-saving-sending-mode-is-after-time-sync/21651/2 "2026-11-12T02:34:49Z")

</div>

Good Day,

Thank you for providing the detailed test results and relevant log entries.

Based on the information provided, the behaviour is directly affected by the selected **Saving/Sending Mode** :

- With parameter `107:0` ( **After Position Fix** ), record generation requires a valid GNSS fix. Therefore, movement triggers a GNSS wake-up and the device exits Online Sleep.

- With parameter `107:2` ( **After Time Sync** ), records can be generated without a valid GNSS fix. In this case, record generation does not itself request a GNSS wake-up, and the device continues using the retained coordinates.

However, since the device changes to the **OnMove** state while GNSS remains powered off indefinitely, this interaction between Asset Movement mode, Online Sleep and parameter `107:2` requires further investigation by our development team.

As a temporary workaround, please continue using `107:0`, as your testing confirms that it correctly wakes GNSS when movement is detected.

To investigate the behaviour with `107:2`, we will need the complete dump logs from both configurations. Please contact your sales manager to create a Partner Portal ticket and attach:

- The dumps collected with `107:2` and `107:0`

- The configuration files used for both tests

- The device IMEI

- Exact timestamps for each reproduced occurrence

- The corresponding server records

The development team can then confirm whether this is the intended firmware logic or whether the OnMove transition should independently power on GNSS and requires a firmware correction.

Thanks, and best regards,  
Imran S.
